Messages
0 Shares

Dual-Winding versus Three-Winding Configurations in 110kV Power Transformers

johnmin ren
Published on Nov 21, 2026

Dual-Winding versus Three-Winding Configurations in 110kV Power Transformers

The number of windings on a 110kV power transformer is a fundamental design choice that shapes its role in the network, its complexity, its cost, and the way it is operated and protected. The two principal configurations are the dual-winding transformer, with a single high-voltage and a single low-voltage side, and the three-winding transformer, which adds a third, usually tertiary, winding to the arrangement. Both are widely used in transmission and sub-transmission service, and the choice between them is driven by the specific requirements of the connection, the load, and the system's need for stabilization or reactive compensation. Understanding the differences between the two is essential for selecting the right configuration and for appreciating how each one serves the network.

A dual-winding transformer is the simpler and more common configuration. It has one winding connected to the higher-voltage system and one winding connected to the lower-voltage system, and it transfers power between the two sides through the magnetic coupling of the common core. The high-voltage winding typically carries the input from the transmission side, and the low-voltage winding delivers power to the distribution or sub-transmission side. The design is straightforward, the operation is intuitive, and the protection scheme is well established, involving standard differential, overcurrent, and earth-fault protection applied to the two windings. For a straightforward step-down connection between two voltage levels, the dual-winding transformer is usually the first choice, offering the lowest cost and the simplest operation for the given duty.

The limitation of the dual-winding configuration is that it has only one path for power transfer and no dedicated point for a stabilizing or reactive element. In some substations, the network requires not only a step-down function but also a point where a tertiary load or a compensation device can be connected. It is in these cases that the three-winding transformer becomes the appropriate solution. A three-winding transformer has a high-voltage winding, a medium-voltage winding, and a tertiary winding, usually rated at a lower voltage. The first two windings perform the main power transfer, while the tertiary winding provides a dedicated connection point for a stabilizing load, a synchronous condenser, a reactor bank, a capacitor bank, or a station service supply.

The tertiary winding serves several important functions. In a system with unbalanced or fluctuating load, the tertiary winding can provide a path for zero-sequence current, which helps to stabilize the neutral point and to limit the effects of phase unbalance. It can also be used to supply reactive power to the network, either by connecting a reactor to absorb reactive power or a capacitor to inject it, supporting voltage control. In some designs, the tertiary winding is connected to a delta configuration, which provides a closed path for triplen harmonics and helps to prevent these harmonics from propagating into the network. The presence of the tertiary winding therefore gives the three-winding transformer capabilities that a dual-winding unit cannot offer.

The design of a three-winding transformer is more complex than that of a dual-winding unit. The core must accommodate three coils, and the designer must carefully balance the leakage impedances between each pair of windings: the high-voltage to medium-voltage impedance, the high-voltage to tertiary impedance, and the medium-voltage to tertiary impedance. These three impedance values must satisfy a mathematical relationship, and they determine how load is distributed between the windings and how the transformer behaves under fault conditions. The winding arrangement, the insulation clearances, and the oil circulation paths must all be designed to accommodate the third coil without compromising the integrity of the main windings. The added complexity is reflected in a higher cost and a larger physical size for the same throughput rating.

Operationally, the three-winding transformer requires more careful protection and monitoring. Because there are three windings, the differential protection must account for the currents in all three, and the protection setting must be coordinated to avoid misoperation under through-fault or internal-fault conditions. The tertiary winding's load must be monitored and managed, as its loading affects the thermal state of the transformer and the distribution of current between the main windings. The operator must understand how the load on the tertiary winding interacts with the load on the main windings, so that the transformer is not overloaded in any part. Despite this added complexity, the three-winding transformer is indispensable where its stabilizing and compensating functions are required.

The choice between the two configurations is therefore driven by the network requirement. If the duty is a simple step-down between two voltage levels, with no need for a tertiary connection, a dual-winding transformer is the economical and appropriate choice. If the substation requires a stabilizing or compensating function, or if the system needs a dedicated point for a tertiary load or a delta path for harmonic control, a three-winding transformer is warranted. In some cases, the decision is influenced by the future needs of the network, and a three-winding unit is selected to provide flexibility for later expansion, even if the tertiary is initially lightly loaded or left unloaded.

It is also worth noting that the configuration affects the transformer's short-circuit capability and its impedance matching. A three-winding transformer has a more complex short-circuit behaviour, and the impedance values between each pair of windings must be coordinated with the system's fault-current levels to ensure that the transformer can withstand the mechanical and thermal stress of a short circuit. The design and testing of a three-winding unit must verify the short-circuit withstand for all relevant fault conditions, making the type-test programme more extensive than for a dual-winding transformer.

For the engineer specifying a 110kV unit, the decision between dual-winding and three-winding should follow a clear analysis of the connection and its requirements. Define the voltage levels to be interconnected, determine whether a tertiary connection is needed for stabilization, compensation, or harmonic control, and select the configuration that provides the required function without unnecessary complexity. A dual-winding transformer is the default for a simple two-sided duty, while a three-winding unit is the right tool when the network demands a dedicated tertiary function.

In both cases, the reliability of the configuration depends on sound design, proper testing, and appropriate protection. Whether the application calls for a straightforward dual-winding 110kV oil-immersed Power Transformer or a more capable three-winding unit, the equipment should be designed to meet the specific network requirement, validated through the appropriate type and routine tests, and operated with a protection and monitoring scheme that reflects the complexity of the configuration. Choosing the right winding arrangement is the first step in ensuring that the transformer will serve the network effectively and reliably for its full service life.

Ultimately, the dual-winding versus three-winding decision is a reflection of the network's needs. The dual-winding unit is the efficient solution for straightforward power transfer, and the three-winding unit is the versatile solution for applications that require an additional stabilizing or compensating function. Understanding the purpose, design, and operation of each configuration allows the engineer to make a confident and well-reasoned specification.